As an Amazon Associate, RackReveal earns from qualifying purchases. Some links on this page are affiliate links, at no extra cost to you.
To make a jump for an RC car, you need a stiff ramp deck, a solid base that can’t slide, and a soft landing area. This guide covers three ways to build one (a quick jump from things at home, a wooden kicker ramp and a dirt jump), how to set the angle and height, safety basics, and five ready-made RC jump ramps if you’d rather buy one. The product details come from each Amazon listing; we haven’t tested these ramps hands-on.
Quick answer: start with a board on a braced base, a low lip and a grass or dirt landing. For a sturdier build, put a stiff deck on a wooden or metal frame that supports it. To skip the build: the 911 Motorsports 2 x 4 ft frame (you add the deck) for 1/10 cars, a foldable 1/8–1/16 ramp, the Freshpark bike-and-RC ramp for big open spaces, or small ramps for 1/18–1/24 and micro cars.
What You Need
- Ramp deck: a stiff sheet that doesn’t flex under your car. On its frame, the maker of the 911 Motorsports ramp recommends one sheet of 1/8 in hardboard (Masonite) for 1/10 cars, two layers for 1/8, or 1/8 in polycarbonate (Lexan) for hard bashing, and says not to use acrylic (plexiglass). Without a full frame under it, use thicker plywood instead.
- Frame or base: plywood offcuts, 2×4 lumber, a sturdy wooden box or bricks.
- Fasteners: wood screws (countersunk if the deck is polycarbonate) and wood glue.
- Something to hold it down: sandbags, bricks or packed dirt behind the ramp.
- Tools: tape measure, pencil, saw, drill or screwdriver, sandpaper, gloves and safety glasses.
Option 1: A Quick Jump From Things at Home
For a first test, lean a stiff board on a solid base: a short stack of bricks, a sturdy wooden box or a step. Weigh down the base and the bottom of the board so neither can slide, keep the lip low, and land on grass or dirt. For 1/18 and smaller cars, a piece of stiff board over a few heavy books works indoors. Cardboard bends under bigger, faster cars, so use it only for minis at low speed.
Option 2: Build a Wooden Kicker Ramp (Step by Step)
- Size the deck. For 1/10 cars, a deck about 2 ft wide is a good start; the 911 Motorsports frame uses a 2 x 4 ft deck. Smaller cars can use a narrower, shorter deck.
- Cut two side pieces. Cut two matching wedge-shaped sides from plywood. Their top edge sets the ramp’s slope; a slightly curved top edge gives a smoother launch than a flat one.
- Join the sides. Screw and glue cross pieces between the sides at the bottom, middle and top so the frame is square and stiff.
- Attach the deck. Screw the deck onto the frame so the cross pieces support it, with no screw heads sticking up. Follow the deck material’s fastening guidance, don’t countersink too deep or overtighten thin sheets, and sand the edges smooth.
- Smooth the leading edge. The front edge should meet the ground flush so the wheels roll on without a bump.
- Brace it. At the jump spot, pack dirt or put sandbags behind the ramp. The 911 Motorsports listing says high-speed hits need this kind of support to hold the ramp in place.
Option 3: Build a Dirt Jump
If you have a yard or a spot where you’re allowed to dig, a dirt jump is free. Pile loose dirt, wet it and pack it hard. Shape a smooth take-off face. Do a few small test jumps to see where the car touches down, then build a wide landing that slopes down and away at that spot, so the car lands on a downslope instead of flat ground. Keep the area between clear. Repack the face after each session; ruts make the car kick sideways in the air.
Angle, Height and Landing
- Angle: at the same speed, a steeper lip sends the car higher; distance depends on the angle, the speed and the landing height together. The 911 Motorsports frame, for example, has leg settings that its maker describes as a long kicker at 40°, a high jump at 50° and back flips at 60°, measured on that frame.
- Height: start low. Ready-made ramps for 1/8–1/16 cars, like the foldable ramp below, stand about 7.5 to 9 in tall.
- Speed and throttle: hit the ramp straight and at a steady speed. On many RC cars, applying throttle in the air raises the nose and braking lowers it; how well this works varies by model, so practise on small jumps first.
- Landing: land on grass, dirt or a downhill landing ramp, not flat concrete. If landings are rough, go back to a lower, slower jump, check that the ramp’s surface is smooth from bottom to lip, and change one thing at a time.
Safety and Car Care
- Jump in an open area away from people, pets, roads and parked cars, and keep everyone out of the landing zone.
- Check the ramp before each session for loose screws, cracks or a sliding base.
- After a session of jumps, check your car for loose screws, bent parts and leaking shocks. See our RC car storage rack guide for keeping cars and parts organized between sessions.
Ready-Made RC Jump Ramps
If you’d rather buy than build, these five ramps were in stock on Amazon US when we checked. Match the ramp to your car’s scale.
| Ramp | Listed scale | Listed size | Build / material |
|---|---|---|---|
| 911 Motorsports frame | Best for 1/10, works up to 1/8 | 24 x 48 in deck | Aluminum frame; deck not included |
| Foldable RC jump ramp | 1/8–1/16 | 7.5–8.9 in tall (footprint conflicts in listing) | Folding; ramp deck board |
| Freshpark portable ramp | Bikes and RC cars | 47 x 24 x 16 in | Urethane/ABS surface; foldable |
| 1/18 & 1/24 ramp set | 1/18 and 1/24 | Not stated | Aluminum frame, nylon surface; 2 pieces |
| Micro RC ramp | 1/14–1/30 and micro | Listing gives 14.5 x 12 in and 18 x 14.5 x 5.1 in | Plastic; snap-together |
As listed on Amazon at the time of writing. Listings change, so check the product page before you buy.
911 Motorsports 2 x 4 ft RC Ramp Frame (1/10 Scale)
An aluminum frame, made in the USA per the listing, that you finish with your own deck: 1/8 in hardboard for normal use or 1/8 in polycarbonate for hard bashing. The listing says it’s best for 1/10 scale and works up to 1/8, takes 30–40 minutes to assemble (closer to 60 with polycarbonate), folds to about 5 in tall. Its item-weight field says 5 lb, while the description says 10–15 lb depending on the kit, so the finished weight with your deck is unclear. The legs adjust between three angle settings.
Best for: 1/10 bashers who want a DIY ramp without building the frame. Skip it if: you want a ready-to-use ramp out of the box; the deck is not included.
- **Frame Only** – Supply your own ramp deck, 1/8″ Masonite for normal use or 1/8″ Lexan for hard bashing. Home Depot has …
- Best for 1:10 scale, but works up to 1:8 Scale RC cars/trucks – **Assembly Required** Check out our store for smaller RT…
- For 1:10 scale a single sheet of 1/8″ masonite is good, use two layers for 1:8 scale cars. Masonite (hardboard) is nice …
Foldable RC Car Jump Ramp (1/8–1/16 Scale)
A folding ramp; the listing gives conflicting footprint sizes (50 x 60 cm in the title, 50 x 80 cm in a bullet), so confirm before you buy. It lists height adjustable from about 7.5 to 8.9 in and a weight of about 4.6 lb. It folds with two screws, and the listing says spare screws are available from the seller. For 1/5 cars, the seller recommends its larger ramps instead.
Best for: 1/10 and 1/8 cars in a backyard or park. Skip it if: you run a 1/5 scale car.
- Durable & Long-Lasting：This RC jumping ramp crafted with high-quality endurance plate, its sturdy structure can bear hea…
- Portable & Space-Saving：Open size: 50 * 80 * 22.5cm (19.7 * 23.6 * 8.86 inches), Height adjustment range19-22.5cm(7.48-8…
- Stable Structure ：The stable design ensures that the RC ramp will not shake during use, offering a secure platform for y…
Freshpark Portable Jump Ramp (Bikes and RC)
A bike jump ramp that also lists RC cars as a use. The listing gives 47 x 24 x 16 in, a weatherproof urethane/ABS riding surface instead of wood, and a folded size of 20 x 20 x 47 in.
Best for: larger RC cars and families who also want a bike ramp. Skip it if: you only run small cars or don’t have room to use and store a 47 in ramp.
- RIDE ANYWHERE, ANYTIME – Perfect for BMX bikes, bicycles, and RC cars, this portable launch ramp transforms any driveway…
- FOLDABLE & EASY TO MOVE – Lightweight design folds down to 20″ x 20″ x 47″, making it simple to transport, store, and se…
- NO WOOD. NO ROT. NO MAINTENANCE – Built with a weatherproof urethane/ABS riding surface that won’t crack, splinter, warp…
RC Car Ramp Set for 1/18 and 1/24 Scale
Two ramp pieces with an aluminum frame and a reinforced nylon surface. The listing describes two slope modes: flat for a gentle angle, or inverted for a steeper one, which needs a wall behind it for support. It’s sold for indoor use with 1/18 and 1/24 cars, and the listing says you can combine several units for 1/10 cars.
Best for: small cars indoors. Skip it if: your car is 1/10 scale or larger and you only want one ramp.
- Durable Material: The ramp surface is made of reinforced nylon, and the frame is constructed from aluminum alloy. It is …
- 2 Adjustable Slope Modes: Use flat for a gentle angle or invert (requires wall support for stability) for a steeper slop…
- Indoor-Friendly Design: Perfect for bedrooms, living rooms, even use while lounging in bed; turns any indoor space into …
Micro RC Car Jump Ramp (1/14–1/30 Scale)
A plastic snap-together ramp with two jump angles, listed for 1/14 to 1/30 and micro RC cars. The listing’s dimension field gives about 18 x 14.5 x 5.1 in, while its title says 14.5 x 12 in, so check the size; it also says heavier or faster cars may need extra support to stop it moving.
Best for: micro and mini RC cars in the living room. Skip it if: you have a heavy or fast car.
- This small-scale jump ramp is designed for 1/14, 1/16, 1/18, 1/24, 1/30 scale and micro RC cars, ideal for jumping and s…
- Made of high-strength plastic, it can withstand repeated jumps from remote control cars.
- Features 2 adjustable jump angles and a detachable snap‑on design for quick assembly in seconds, making it extremely por…
As an Amazon Associate, we earn from qualifying purchases at no extra cost to you.
Black Friday Tip and Gift Idea
Black Friday tip: if you plan to buy an RC ramp on Black Friday 2026 (November 27) or Cyber Monday (November 30), note your car’s scale now, measure the space where you’ll jump, and shortlist ramps listed for that scale. Then check the current price on Amazon on the day rather than a “was” price.
Gift idea: a jump ramp is a fun add-on gift for someone who already has an RC car. Confirm the car’s scale first; a ramp sized for micro cars won’t suit a 1/10 basher. Our affordable RC car picks cover the car itself.
FAQ
How do I make a simple jump for an RC car at home?
Lean a stiff board that doesn’t flex under your car, such as a thick piece of plywood, on a solid base like a short stack of bricks or a sturdy wooden box. Weigh down or brace the base so it can’t slide, start with a low lip and slow passes, and land on grass or dirt rather than concrete.
What is the best material for an RC car ramp?
On a supporting frame, hardboard (Masonite) is cheap and easy to work with, and polycarbonate (Lexan) is tougher for hard bashing. The maker of the 911 Motorsports frame above recommends 1/8 in sheets of those two for its frame and says not to use acrylic (plexiglass). For a ramp without a full frame underneath, use a thicker deck, such as plywood, that doesn’t flex under your car.
What angle should an RC jump be?
There is no single right angle. At the same speed, a steeper lip sends the car higher; how far it goes depends on the angle, the speed and the landing height together. Start low and slow, make small changes and watch how the car lands before going bigger.
How big should an RC jump be for a 1/10 scale car?
Ready-made ramps listed for 1/10 cars are about 2 ft wide; the foldable ramp above stands about 7.5 to 9 in tall, and the 911 Motorsports frame takes a 2 x 4 ft deck. Build within that range and only go bigger once your landings are consistent.
How do I build a dirt jump for RC cars?
Pile loose dirt, wet it and pack it hard, then shape a smooth take-off face. Find where the car touches down with small test jumps, then build a wide downhill landing there and keep the area between clear. Keep the face smooth so the car doesn’t kick sideways, and repack it after each session.
Can I use a bike or skateboard ramp for an RC car?
Yes, many portable bike ramps list RC cars as a use, like the Freshpark ramp above. The Freshpark ramp is 47 x 24 x 16 in, so it suits larger cars and needs open space and storage room.
🛠️ Buying Gear for Your Work Truck?
A free Amazon Business account gets you bulk pricing, tax-exempt purchases, and business-only deals on tools, racks, and truck accessories.
Create Free Amazon Business AccountAs an Amazon Associate we earn from qualifying purchases.
